Merc 3D Parts
ContributorR
Profile306 parts in stock

@Razzmatazz

306 PARTS
Parts in stock
24 entries
Part1573
Mirror-Adjustment Handle

Mirror-Adjustment Handle

Two-piece handle and lock for the 5 mm manual driver-side mirror adjustment rod. The creator explicitly states W123, W124, W201 and W126 fitment. Use tough cabin material, check the rod diameter and locking engagement, and confirm full mirror travel without forcing the cable or mechanism.

ABS · Nylon · PETGMirrors
Fits190 Series W201 · E-Class W124 / S124 / C124 / A124 · S-Class W126 / C126 · W123 Series W123 / S123 / C123
024by Ward Vandenbroucke (WvdbID)
Part1860
Parcel Shelf Hinge Pair

Parcel Shelf Hinge Pair

Left and right replacement hinges for the rear parcel shelf. The original source supplies both handed files and a physical comparison image; a later credited remix explicitly identifies this original design as the W177 parcel-shelf hinge and retains the same interface while adding reinforcement. Print the original files on their flat sides at 0.16 mm, with four walls and no supports; the creator suggests fuzzy skin only on the four towers that enter the parcel shelf. A later source specifies PETG for this cabin/cargo application. Inspect layer adhesion and both pivots, confirm free movement, and avoid loading the shelf until both hinges are fully seated. No Mercedes number is assigned: A1776905400 identifies the complete parcel shelf, not either printed hinge child.

PETGCabin trim, cargo & roof
FitsA-Class W177
022by neofa
Part1767
Factory Phone-Cradle Adapter Plate

Factory Phone-Cradle Adapter Plate

Adapter plate that replaces the obsolete factory phone cradle while reusing its original dashboard bracket and screws, with variants for a Brodit MoveClip mounting pattern and alternate screen position. Source photographs show the bracket, plate and phones installed. Match the equipped cradle and screw lengths, use cabin-heat-resistant material, and confirm the device cannot obscure instruments, controls, airbags or the driver view.

ABS · Nylon · PETGConsole & storage
FitsVito / Viano / V-Class W639
020by moWerk
Part1646
Zip-Tie Cup Holder

Zip-Tie Cup Holder

Custom cup holder that the creator states is made for this vehicle generation and attached with a zip tie. The publication supplies one STL and only a CAD-render source image; it gives no material, print settings, exact mounting location or long-term test evidence. Check container diameter, attachment-point strength and clearances, use cabin-heat-resistant material and secure it so neither the holder nor a drink can obstruct controls or occupants or become loose under braking.

ABS · PETGConsole & storage
FitsG-Class W463
020by jeremia joki-erkkilä (jeremiajokierkkila)
Part1718
Centre-Console Dual Cup Holder

Centre-Console Dual Cup Holder

Two-piece dual cup holder designed to insert into the centre-console cupholder while preserving access to the 12-volt socket, armrest and selector. The source supplies cup and stand STLs plus a CAD image but no container-size or crash-retention test. Use cabin-heat-resistant material, check console and selector clearance and test only with cold, closed containers before road use; confirm the assembly cannot detach or spill into controls under braking.

ABS · Nylon · PETGConsole & storage
FitsC-Class W203 / S203 / CL203
016by Jonas Katona (ThinkAndPrint)
Part1568
Sun-Visor Retaining Clip

Sun-Visor Retaining Clip

Two-piece retaining clip and screw cover for the cabin sun visor. The creator made it for a 1989 300E and explicitly states W123, W124, W126, W140 and W201 fitment, while noting that it does not carry electrical contacts for illuminated vanity mirrors. Print the main clip and locking cover in the documented orientations, use cabin-heat-resistant material, compare the screw position and visor profile, and confirm secure retention and free release before driving.

ABS · Nylon · PETGCabin trim, cargo & roof
Fits190 Series W201 · E-Class W124 / S124 / C124 / A124 · S-Class W126 / C126 · S-Class W140 / C140 · W123 Series W123 / S123 / C123
014by Robot Barnard (RobotBarnard)
Part1777
Manual Seat-Slide Adjustment Handles

Manual Seat-Slide Adjustment Handles

Direct-replacement manual seat adjustment handles supplied as separate left- and right-hand files. The creator designed them for a 2007 vehicle and identifies the right-hand component as original part A1699190661; Mercedes genuine-parts and PartSouq listings corroborate that number as the right-side seat-adjustment lever. The OEM number applies to the right-hand file only. Use a tough, heat-resistant material, compare the mounting socket and travel with an intact handle, and verify that the seat locks positively in every tested position before driving.

ABS · Nylon · PETGSeats & restraints
FitsA-Class W169
010by Ивелин Илиев (option)
Part1677
Dashboard Side Vent

Dashboard Side Vent

Replacement dashboard side vent explicitly identified for 1997–2004 SLK 230 Kompressor cars. The source photograph shows a physical vent installed in the dashboard; the creator recommends high-temperature PLA or PETG and reports a FILACUBE HT-PLA print survived a Texas summer with very little distortion. Match the side-vent opening and original vane function, use cabin-heat-resistant material and verify secure seating and unrestricted airflow and adjustment.

ABS · PETGDashboard & controls
FitsSLK / SLC R170
010by Patrick McSweeney
Part1826
Display-Side Phone Holder

Display-Side Phone Holder

Phone holder designed to fit beside the dashboard display. The author supplies a base holder and phone-specific variants for iPhone 11, iPhone 8 Plus, and the 2016 iPhone SE, and shows a physical holder fitted in the vehicle. The creator used heat-resistant Extrudr GreenTEC rather than ordinary PLA, which can soften in a hot cabin. Choose only the matching variant, confirm secure retention, and keep the device clear of the driver’s view, controls, airbags, and ventilation.

ABS · PETGDashboard & controls
FitsA-Class W176
09by Ro Pa (Umbi1987)
Part1845
Two-Level Center-Armrest Organizer

Two-Level Center-Armrest Organizer

Two-level center-armrest organizer source-backed for 2015–2021 C-Class interiors and the corresponding GLC console. The upper tray includes Canadian coin slots, a phone compartment and general storage; the lower tray catches loose items. Source imagery is CAD and slicer evidence only. Verify the 258×123×65 mm envelope before printing, ensure the lid closes freely, and do not place items where they can jam the console or controls.

ABS · Nylon · PETGConsole & storage
FitsC-Class W205 / S205 / C205 / A205 · GLK / GLC X253 / C253
08by KTiftik
Part1829
Center-Console Phone Holder

Center-Console Phone Holder

Two alternative phone-holder files designed to sit in the middle-console compartment for A180 and A200 variants. The creator states compatibility with iPhone and Android devices, simple installation, and support-free printing; source photos show the holder installed with a phone and charging cable. Choose one alternative file, verify a stable fit with the specific phone and case, use a cabin-heat-resistant material, and keep the device and cable clear of the selector and other controls.

ABS · PETGConsole & storage
FitsA-Class W176
08by Iason Argyrakis
Part1638
Dashboard Air-Vent Direction Tab

Dashboard Air-Vent Direction Tab

Replacement outer tab for adjusting dashboard air-vent direction. The source explicitly identifies SL roadster fitment and states that only the visible outer portion is modeled; its sole source image is a CAD render. Compare the vent version and remaining inner mechanism, use cabin-heat-resistant material, deburr the contact surfaces and verify unrestricted vane travel without stressing the original vent.

ABS · PETGDashboard & controls
FitsSL R129
08by Jan Stříbrný (pitomeceprdici)
Part1581
Seat-Cushion Upholstery Clip

Seat-Cushion Upholstery Clip

Replacement clip joining seat upholstery to the internal metal rod. The creator explicitly states use on W123, W140 and R129 seats and recommends ABS rather than PLA. Compare the original clip and seat construction, use a tough heat-resistant material, round and clean every contact edge and confirm the upholstery is retained without cutting the fabric or affecting seat adjustment. Source-stated numbers 1239884078 and 1409883778 were not assigned because an independent exact EPC child-component mapping was not recoverable in this run.

ABS · Nylon · PETGSeats & restraints
FitsS-Class W140 / C140 · SL R129 · W123 Series W123 / S123 / C123
08by (Preador)
Part1772
Electrical Fuse-Box Latch Clip

Electrical Fuse-Box Latch Clip

Replacement latch clip for the engine-compartment electrical fuse box, identified by the creator as the exact serviced child. Source photographs compare it with the original and show it retaining the lid. Print in engine-bay-temperature-resistant PETG, ABS or nylon, verify the box and latch version, and confirm the lid seals and remains secured without pinching wiring.

ABS · NylonEngine-bay electrical & sensors
FitsVito / Viano / V-Class W639
07by moWerk
Part1703
Door Wood-Trim Retaining Clip

Door Wood-Trim Retaining Clip

Replacement retaining clip for the interior door wood trim. The creator identifies exact 220-series fitment, recommends flexible FilaFlex material, and the preserved source photographs show the loose printed clip, the wood trim installed and the door with the trim removed. The creator does not provide a molded Mercedes number. EPC evidence lists several position-specific clips and clamps around W220 door and pillar panelling, but does not establish which exact serviced child this geometry reproduces, so no OEM number is assigned. Compare the original clip, door position, trim profile and production/option version, fit without forcing the veneer, and confirm the wood trim is fully retained without rattles or interference.

TPUInterior doors & windows
FitsS-Class W220
07by Gabriel Giner (Gabiginer)
Part1645
Windscreen-Wiper Spindle Nut Cover

Windscreen-Wiper Spindle Nut Cover

Small cover for the windscreen-wiper spindle nut on 1990s vehicles. The source shows the physical cover fitted around a wiper pivot and supplies one STL, but states no material or print settings. Match the spindle and nut dimensions, use weather-, UV- and heat-resistant material, preserve full wiper-arm clearance and verify complete sweep and secure retention before road use.

ABS · Nylon · PETGWipers & washers
FitsG-Class W463
07by Ebo Lompedo (Ebolompedo)
Part1612
Double-DIN Radio Adapter Frame

Double-DIN Radio Adapter Frame

Custom adapter frame for the specific 7-inch double-DIN Android head unit linked by the creator. Source photographs show the printed frame and the modified centre-console opening. Confirm the radio dimensions and console cut-out before printing, protect the veneer and wiring, provide adequate ventilation and strain relief, and do not assume other double-DIN units share the same bezel geometry.

ABS · PETGDashboard & controls
Fits190 Series W201
07by villetahtinen
Part1598
Ashtray-Replacement Storage Set

Ashtray-Replacement Storage Set

Multi-part replacement for the centre-console ashtray: a storage body plus shallow, flush, blank and outlet-ready plate options. The creator shows the body installed and notes unused space beneath the extended plate for a separately wired 12-volt or USB outlet. Use heat-resistant material, retain safe selector clearance, secure the assembly, and fuse and insulate any electrical addition independently; the files contain no electrical hardware.

ABS · Nylon · PETGConsole & storage
FitsW123 Series W123 / S123 / C123
07by Garrett Johnson
Part1774
Speaker Adapter Ring

Speaker Adapter Ring

Sturdy adapter ring for fitting aftermarket speakers to the stock front-door or rear-side mounting pattern. The creator reports precise alignment with the factory screw holes and supplies installed source photographs. This is an aftermarket adapter rather than any listed speaker assembly, so no speaker OEM number is assigned. Verify speaker diameter, depth, window and trim clearance, seal against rattles and moisture, and secure wiring away from moving mechanisms.

ABS · Nylon · PETGInterior doors & windows
FitsVito / Viano / V-Class W639
06by moWerk
Part1621
Front-Right Sill-End Cap

Front-Right Sill-End Cap

Replacement cover for the front-right opening in the side-member/sill cladding. Source photographs show the installed location, the original and printed pieces, and the CAD model. EPC evidence identifies the right-front covering; use UV-, weather- and impact-resistant material, inspect the mounting opening for corrosion, and confirm the cap remains secure.

ABS · Nylon · PETGBody panels & exterior trim
Fits190 Series W201
06by slyd1ck
Part1784
Fuel-Cap Retaining Tether

Fuel-Cap Retaining Tether

Three-part retaining tether for the fuel cap, explicitly shown by the creator on an R171 and described as fitting many Mercedes fuel caps. The design comprises a cap ring, flexible cord, and eyelet. The source used ASA for the ring and hard Shore D56 TPU for the cord and eyelet, while noting that approximately Shore A95 TPU may also work. Install all three parts, verify the ring does not interfere with cap sealing or locking, keep the tether clear of the filler neck and hinge, and replace it if fuel exposure, heat, or repeated flexing causes cracks or loss of retention. No other generation is linked because the creator does not identify one and no exact child-component number was established.

TPUDoors, bonnet, boot & bed hardware
FitsSLK / SLC R171
05by Gerhard A. (Gerry0)
Part1776
Floor-Mat Retaining Clip Set

Floor-Mat Retaining Clip Set

Two-piece retaining clip for the driver's floor mat. The creator designed and tested it on a 2011 vehicle, states that the two halves permanently snap together through the mat, and notes that removal from the floor takes slightly more force than the original. The source print used PLA with a 0.4 mm nozzle, no raft and no supports; for sustained cabin heat, prefer an automotive-temperature-capable material. Confirm that both halves are fully locked, that the mat cannot slide toward the pedals, and stop using the print if it loosens or cracks.

ABS · Nylon · PETGCabin trim, cargo & roof
FitsA-Class W169
05by Stefan Rosgaard (eskimo)
Part1773
Interior Panel Retaining Clip

Interior Panel Retaining Clip

Replacement push clip for interior trim panels, identified by the creator as the exact child and accompanied by an EPC-style source diagram. Print in tough cabin-heat-resistant material, compare head and stem dimensions with an original clip, use only in the stated non-structural trim position, and confirm the panel is secure without interfering with wiring, airbags or seat mechanisms.

ABS · Nylon · PETGInterior doors & windows
FitsVito / Viano / V-Class W639
05by rotoli
Part1854
Dashboard Tablet Mount

Dashboard Tablet Mount

Two-piece mount designed for a 2018 GLC and a 12.9-inch sixth-generation iPad Pro. The vehicle-side piece slips over the factory display and accepts a soft-opening hinge so the tablet can be moved for rear-camera use. Source imagery is CAD/render evidence only. Verify the exact tablet and hinge hardware, protect the factory screen and trim, secure and strain-relieve all wiring, preserve visibility of the road, instruments and reversing image, and remove the mount if it loosens, obstructs controls, or overheats.

ABS · NylonDashboard & controls
FitsGLK / GLC X253 / C253
04by Thom Boessel (ThomBoessel)

24 of 306 shown